DESCRIPTION: We will custom mount your Leupold Delta Point Pro red dot optic on the slide as described below, please check the Compatibility tab above to verify we can cut your slide model. We do a custom mount that requires milling of the slide to reduce the overall profile of the optic, bringing it down closer to the bore by lowering is 0.150". Unfortunately, due to the overall base height of this optic, it still sits too high for acceptable co-witnessing with typical suppressor height iron sights. The best solution we've found it to use the Leupold Delta Point Pro rear iron sight that is mounted to the rear of the optic and a Dawson Precision front sight with the appropriate height to cowitness through the optic. As such, we only offer this optic mounted such that the add on rear iron sight is roughly flush with the rear of the slide. We are careful not to alter the function or reliability of the internal workings of the slide.
SPECIAL NOTES: This product is a machining operation only. It does not include refinishing of the exposed metal, that is sold separately. It does not include the actual optic.
RECOMMENDED ACCESSORIES: Bare metal is exposed when we provide this product, thus refinishing is recommended to prevent rust/oxidation. Refinishing options and associated cuts/parts are highlighted below in the Accessories section.
LEO/MIL/1ST RESPONDER: We refund 10% on machining and refinishing options to LEO/MIL/1ST RESPONDERS with valid credentials. You need to send us via text/email/with your package, a copy of your credentials. We refund the 10% upon completion of the work. This item qualifies for the discount.
COMPATIBILITY: This optic cut is compatible with most other slide mods we offer, see specific model details below.
GLOCK (All models except slimline [G42,43,etc.], G41 and G17L)This mounting package mounts a Leupold Delta Point Pro only, forward of the rear iron sight on Glocks. The front and rear wall of the inlet will be cut to match the optic perfectly, as well as bosses for the forward indexing points, thereby providing additional stabilization/locating points. On Glocks, the mount will preserve the original OEM dovetail for the rear site, however there is a risk for blemish here. Like any machined production part, Glock slides are at risk for stacked tolerances. If your slide has just the right combination of stacked tolerances, the DP Pro's cut can on some slides, just barely invade the striker block channel. This creates a small hole communicating between the bottom side of the channel into the DP Pro's cut. You can see an example of this in the last photo above. This breech creates a blemish which is only view able with the optic removed from the slide. It does not create a function issue, it doesn't create a safety issue. We feel we must be forthcoming however and advise that should you order this cut with your Glock slide, you're accepting the risk for this blemish. If you need us to install/change your iron sites, or just disassemble/reassemble your slide, please add the armorer fee to your shopping cart, that will cover the sites swap. Of course we will need the sites if you're not purchasing them from us.... If you're purchasing new irons, they must be tall enough to co-witness. This machining will expose raw steel which we recommend refinishing to prevent oxidation/rusting. We offer Cerakote and PVD options separately. We DO offer a slide blank now for the DeltaPoint Pro, we have blanks for all Glock models.SMITH & WESSON (M&P 9/40/9c/40c)We can mount your Leupold Delta Point Pro on your S&W M&P's using the same style inlet mount as described above in the Glock section. The original rear sight dovetail is however eliminated, there is no striker channel blemish issue. Keep in mind the optic is mounted such that your striker safety plunger and spring assembly will be captured by the optic similar in fashion to how it's captured by the rear iron sight on the OEM slide.
CZ (TACTICAL SPORT/SHADOW 2)We can mount your Leupold Delta Point Pro on your CZ's making them perfect for competition. We are able to seat the optic very low getting the sight over bore minimized. If you're trying to get your Shadow 2 USPSA Carry Optics ready, please take a look at the CZ Shadow 2 Carry Optics package instead.
OTHER SLIDESWe have yet to cut a Delta Point Pro inlet on any other makes besides CZ, Glock and S&W. We will be happy to consider other options such as HK and Sig. However these are on a case by case basis and armorer's fees may be different. We require prior contact and approval before accepting other slides. Please contact us via email first.
OPTIONS AVAILABLE: We now offer a blank for this cut but only for Glocks. Your blank will be fitted to your slide and is made of 6061 aluminum. We can Cerakote the blank to match your slide. The aluminum blank cannot be black nitrided nor can it be PVD coated. If you've opted for a copper finish on the slide (TiCN), we suggest armor black Cerakote for the blank, the contrast looks pretty cool.